0,8 - 3 mm aluminium AL99 AW 1050A H14/H24

0,8 - 3 mm aluminium AL99 AW 1050A H14/H24

SKU: 103192

from

1,19 €

incl. VAT , from 7,90 € Shipping costs

119,00 € per 1 m²

wide in mm / inch
Thickness mm / inch
Length in mm

Category: Sheets
Manufacturers: rapa GmbH

Available immediately

This item has variations. Please select the requested variation.

Aluminium panel
Material: Aluminium single-sided laminated AL99 AW 1050A H14/H24
EN 573-3 / EN 485-1 in different lengths and widths, please select your desired size.

Material properties
Use in contact with food: Yes
Weldability: gas = good, WIG = good, MIG = satisfactory
Surface treatment: protective anodizing = very good, decorative anodizing = satisfactory, paint/coating = very good
Cold formability: bending, pressing, deep drawing, upsetting, impact extrusion = very good
Corrosion resistance: weathering good, sea water = satisfactory
Solderability: hard soldering, friction soldering, soft soldering = very good

Use:
Vehicle and shipbuilding
food industry
apparatus engineering
architecture
model building

This item is also available made to measure in our online shop. You can find it under the following link:

- Aluminium sheet made to measure with 0.8mm thickness:
https://www.schmiedekult.de/08-mm-Aluminium-sheet-made-to-measure

- Aluminium sheet made to measure with 1mm thickness:
https://www.schmiedekult.de/1-mm-Alublech-Alu-Blech-Aluminium-Blechzuschnitt-bis-1-m

- Aluminium sheet made to measure with 1.5mm thickness:
https://www.schmiedekult.de/15-mm-aluminium-sheet-made-to-measure-aluminium-sheet-aluminium-sheet-cut-to-size

- Aluminium sheet made to measure with 2mm thickness:
https://www.schmiedekult.de/2-mm-Alublech-nach-Mass-Alu-Blech-Aluminium-Blechzuschnitt

- Aluminium sheet made to measure with 3mm thickness:
https://www.schmiedekult.de/3-mm-Alublech-nach-Mass-Alu-Blech-Aluminium-Blechzuschnitt

Attention: the sheets are film coated on one side and may have scratches on the reverse side. The cut edges are not deburred!
The cutting tolerance for sheets is +- 2 mm.

Product type:	Metal Sheet
Material:	Aluminum
Material:	AW-1050 (Al99,5)
Content, if no desired size is used.:	0,01 m²

There are no reviews yet.

Contact data

First name - optional

Last name

Company - optional

E-Mail

Phone - optional

Question about item

Your question

I agree that my data will be stored permanently for contacting and allocation for possible queries. Note: You can revoke this consent at any time by sending us a message. In the event of revocation, we will delete your data immediately. For further information, please refer to the Privacy Policy. ()

Manufacturer information:

rapa GmbH

Duisburger Str. 71

Emmerich am Rhein, 46446

Deutschland

gpsr@schmiedekult.de

/rapa GmbH

Information on product safety:

Warning notices

Caution! The sheet metal could have sharp cutting edges that could cut you. As we do not know for what purpose the sheets are used, we unfortunately cannot deburr them without interfering with any weld seam preparations. For this reason, we recommend wearing cut-resistant gloves!
Keep away from other metals! Aluminum should never be brought into direct contact with other metals because contact corrosion can occur. Contact corrosion can weaken both the aluminum and the other metal.

Only process with respiratory protection!

has health risks

Weld only with fume extraction! Aluminum may only be welded with an appropriate fume extraction system and using suitable respiratory protection. The gases produced during welding can cause severe health damage.